Old Glory: Touch-Free Active Foam Vehicle Wash
Fast. Foamy. Freedom-level clean.
When you need high-powered cleaning without scrubbing, Old Glory is your go-to single-step solution. Built for touch-free vehicle washing, this alkaline-based foam soap cuts through road grime, salt, and bugs with ease—without the need for brushes or mitts.
Whether you’re washing a truck, fleet vehicle, or your daily driver, this guide will walk you through everything you need to know to get the most out of Old Glory
What is Old Glory?
Old Glory is Chem-X’s high-pH, single-step active foam soap designed for fast and effective touch free cleaning. It’s engineered to:
- Break down road film, bugs, and grease
- Foam heavily for dwell time and visual coverage
- Rinse clean without leaving residue
- Work on paint, chrome, wheels, plastics, and more
Unlike 2-step acid/alkaline systems (like Stars + Stripes), Old Glory simplifies your wash process into one powerful foaming step—ideal for high-volume or quick-turn washes.
Key Features
Touch-Free Cleaning
Cuts through grime without the need for scrubbing or contact.
High Foaming Action
Designed to work through foam cannons and injectors for full coverage.
Versatile Application
Can be used via foam cannon, pump sprayer, or downstream injector.
Fast Rinse-Off
Formulated to rinse clean with high pressure, leaving no residue or film.
Safe for Most Finishes
Safe on clear coat, glass, and plastics—just avoid polished aluminum unless heavily diluted.
How to Use Old Glory
Old Glory works across a variety of setups. Here's how to apply it based on your equipment:
Foam Cannon (Chrome Cannon 2.0 or MTM PF22.2)
Mix Ratio: 1 part Old Glory to 4 parts water (1:4) in your foam cannon bottle
Pressure Washer Output: Ideal PSI 1500–4000 | GPM 2.0–5.3
Application:
- Rinse vehicle to remove loose debris.
- Foam entire vehicle with Old Glory solution.Is o
- Allow to dwell for 30–60 seconds (do not let dry).
- Rinse thoroughly with high pressure.
Pump Sprayer
- Mix Ratio: 1 part Old Glory to 100 parts water (1:100)
- Best for spot-cleaning or when pressure washing isn’t available.
- Apply to a wet surface, allow short dwell, then rinse.
Power Washer Injector (e.g., ST-160 or ST-164)
- Run Ratio: 100:1 PIR
- Pre-dilute soap in a 5-gallon pail if necessary to match injector draw rate.
- Apply evenly, dwell, and rinse with high pressure.
⚠️ Safety & Surface Notes
- Do NOT allow Old Glory to dry on the surface—especially in direct sunlight.
- Avoid use on polished aluminum unless diluted beyond 100:1 and used with caution.
- Test on sensitive finishes before full application.
- Always rinse thoroughly to prevent spotting or streaks.
FAQs
Is Old Glory safe for ceramic coatings?
Yes—but use with caution and do not let it dwell too long or dry on the surface. Rinse quickly and follow with a protective sealant like Snake Oil.
Can I use Old Glory in direct sunlight?
It’s best not to. Apply in shade or early morning to prevent drying on the surface.
Can I use Old Glory with Snake Oil?
Absolutely! After rinsing Old Glory, apply Snake Oil to the wet surface, let it dwell briefly, then rinse again for a hydrophobic, protected finish.
Pro Tip: Pair It With the Right Gear
Old Glory works best when paired with:
- Chem-X Chrome Cannon 2.0
- ST-160 or ST-164 Injector
- High-pressure rinsing (1500+ PSI)
If you're looking for a complete bundle, check out the Old Glory Chrome Cannon Kit for a ready-to-go setup.
Who Should Use Old Glory?
Old Glory is a favorite for:
- Fleet owners who need fast, consistent results
- Detailers looking to speed up wash cycles
- DIYers who want professional-grade foam without the hassle of a 2-step process
The Name Says It All
Old Glory is more than a soap—it’s a declaration of clean. When time is short and performance matters, trust this high-foaming, touch-free powerhouse to get the job done with minimal effort and maximum results.